Update wren-c5-esphome.yaml

YAML Examples/WREN C5/wren-c5-esphome.yaml

@@ -1,11 +1,46 @@
+# Dave Williams, DitroniX 2019-2026 (ditronix.net)
+# WREN | ESP32-C5 Recliner Linear Motor Controller | IoT Home Automation
+
+# Example Code, to demonstrate and test the WREN C5
+
+# Remember!
+# - Set the BOARD to Use ESP32C5 Dev Module (or similar).
+# - You can also set the BAUD rate up to 921600 to speed up flashing.
+# - The SDK does NOT need external power to flash.  It will take Power from the USB 5V.
+# - The Serial Monitor is configured for BAUD 115200
+
+# The purpose of this test code is to cycle through the various main functions of the board as part of bring up testing.
+
+# This test code is OPEN SOURCE and formatted for easier viewing.  Although is is not intended for real world use, it may be freely used, or modified as needed.
+# It is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+
+# For board configuration, see:
+
+# * github.com/DitroniX/WREN-Recliner-Linear-Motor-Controller-IoT-Home-Automation/wiki/Arduino-IDE
+# * github.com/DitroniX/WREN-Recliner-Linear-Motor-Controller-IoT-Home-Automation/wiki/PlatformIO-ESP32%E2%80%90C5
+# * github.com/DitroniX/WREN-Recliner-Linear-Motor-Controller-IoT-Home-Automation/wiki/Home-Assistant-and-ESPHome
+# * github.com/DitroniX/Home-Assistant-Dev
+
+# Further information, details and examples can be found on our website or github.com/DitroniX
+
+# * ditronix.net
+# * github.com/DitroniX
+# * github.com/DitroniX/WREN-Recliner-Linear-Motor-Controller-IoT-Home-Automation
+# * github.com/DitroniX/WREN-Recliner-Linear-Motor-Controller-IoT-Home-Automation/wiki
+# * github.com/DitroniX/WREN-Recliner-Linear-Motor-Controller-IoT-Home-Automation/wiki/FAQ
+# * hackster.io/DitroniX/
+# * hackster.io/DitroniX/wren-esp32-c5-recliner-linear-motor-controller-iot-rs485-e2b397
+
+# This YAML code has been created to show the features and functionality of WREN C5.
+# This code has expanded to become an all encompassing ESPHome applicaition and is a fully working baseline.
 
 esphome:
   name: wren-c5
+  friendly_name: WREN C5
 
   on_boot:
     priority: 800
     then:
-
       - lambda: |-
 
           uint8_t cfg[2] = {0x03,0x00};
@@ -22,28 +57,65 @@ esphome:
             "TCA6408A initialized"
           );
 
-
       - delay: 500ms
 
       - if:
           condition:
             binary_sensor.is_on: sflag
           then:
-            - logger.log:
+            - logger.log: "SFLAG ACTIVE AFTER BOOT"
-                "SFLAG ACTIVE AFTER BOOT"
+            - script.execute: fault_handler
-            - script.execute:
-                fault_handler
 
 esp32:
-
   board: esp32-c5-devkitc-1
   variant: esp32c5
 
   framework:
     type: esp-idf
 
-i2c:
+################################## ESPHOME ##################################
 
+# ======================== ESPHome - Enter Below your Key/Pasawords ===========================
+
+api:
+  encryption:
+    key: !secret wren_c5__encryption_key
+ota:
+  - platform: esphome
+    password: !secret wren_c5__ota_password
+
+wifi:
+  ssid: !secret wifi_ssid
+  password: !secret wifi_password
+  ap:
+    ssid: WREN C5 Fallback Hotspot
+    password: !secret wren_c5__ap_password
+captive_portal:
+
+logger:
+
+################################## SUBSTITUTIONS ##################################
+substitutions:
+  # ======================== About ===========================
+
+  author: "DitroniX - Dave Williams"
+  firmware_version: "1.00.02"
+  release_date: "2026-06-21"
+  board_name: "WREN C5"
+  board_mcu: "ESP32-C5"
+  board_rev: "1.2606.104"
+
+  # ======================== Config ===========================
+
+  board_location: "Lounge"
+  voltage_low: 3.00
+  voltage_high: 48.0
+
+################################## SETUP ##################################
+
+# ========================== GPIO =============================
+
+i2c:
   id: bus_a
 
   sda: GPIO2
@@ -52,19 +124,18 @@ i2c:
   scan: true
 
 globals:
-
   - id: fault_active
     type: bool
     restore_value: no
-    initial_value: 'false'
+    initial_value: "false"
 
   - id: tca_state
     type: uint8_t
     restore_value: no
-    initial_value: '0'
+    initial_value: "0"
 
+################################## SWITCH ##################################
 switch:
-
   - platform: gpio
     id: rs485_enable
     pin: GPIO23
@@ -75,13 +146,171 @@ output:
     pin: GPIO27
     id: blue_led
 
+################################## LIGHT ##################################
 light:
   - platform: binary
     id: heartbeat
     output: blue_led
 
-binary_sensor:
+################################## TEXT SENSOR ##################################
 
+text_sensor:
+  # =====================================================
+  # WREN C5 FIRMWARE METADATA
+  # =====================================================
+
+  - platform: template
+    name: "Author"
+    entity_category: diagnostic
+    lambda: |-
+      return {"${author}"};
+
+  - platform: template
+    name: "Firmware Version"
+    entity_category: diagnostic
+    lambda: |-
+      return {"${firmware_version}"};
+
+  - platform: template
+    name: "Release Date"
+    entity_category: diagnostic
+    lambda: |-
+      return {"${release_date}"};
+
+  - platform: template
+    name: "Board Name"
+    entity_category: diagnostic
+    lambda: |-
+      return {"${board_name}"};
+
+  - platform: template
+    name: "Board MCU"
+    entity_category: diagnostic
+    lambda: |-
+      return {"${board_mcu}"};
+
+  - platform: template
+    name: "Board Build"
+    entity_category: diagnostic
+    lambda: |-
+      return {"${board_rev}"};
+
+  - platform: template
+    name: "Board Location"
+    entity_category: diagnostic
+    icon: mdi:information
+    update_interval: 60s
+    lambda: |-
+      return {"${board_location}"};
+
+  - platform: template
+    name: "Product"
+    icon: mdi:information
+    entity_category: diagnostic
+    update_interval: 60s
+    lambda: |-
+      return {"Professional Energy Monitor"};
+
+  - platform: template
+    name: "Hardware"
+    entity_category: diagnostic
+    icon: mdi:information
+    update_interval: 60s
+    lambda: |-
+      return {"ESP32-C5 Dual ATM90E32"};
+
+  - platform: template
+    name: "WiFi Signal Quality"
+    id: wifi_signal_quality
+    entity_category: diagnostic
+    update_interval: 30s
+    lambda: |-
+      if (!id(wifi_signal_db).has_state()) {
+        return {"No Signal"};
+      }
+
+      int rssi = abs((int)id(wifi_signal_db).state);
+
+      if (rssi <= 30) {
+        return {"Signal Very Strong"};
+      } else if (rssi <= 50) {
+        return {"Signal Excellent"};
+      } else if (rssi <= 60) {
+        return {"Signal Healthy"};
+      } else if (rssi <= 70) {
+        return {"Signal Very Good"};
+      } else if (rssi <= 80) {
+        return {"Signal Good"};
+      } else if (rssi <= 90) {
+        return {"Signal Poor - Try Moving Position"};
+      } else if (rssi <= 100) {
+        return {"Signal Very Low - Move Position"};
+      } else {
+        return {"No Signal"};
+      }
+
+  # =====================================================
+  # VOLTAGE STATUS AND LOG
+  # =====================================================
+
+  - platform: template
+    name: "Supply Status"
+    id: supply_status
+    icon: mdi:power-plug
+    entity_category: diagnostic
+    update_interval: 1s
+    lambda: |-
+      float v = id(supply_voltage).state;
+
+      constexpr float VOLTAGE_LOW  = ${voltage_low};
+      constexpr float VOLTAGE_HIGH = ${voltage_high};      
+
+      // Developer. Only enable for PCB 1.2606.104 and above, as this value is now taken from +VBUS rather than P24V_DVR
+      // if (v >= VOLTAGE_LOW && v <= 5.5f) {
+      //   ESP_LOGI(
+      //    "POWER",
+      //     "USB Power Detected - Supply Voltage %.2fV",
+      //    v
+      //   );
+      //   return {"USB Powered"};
+      // }
+
+      if (v >= 5.5f && v <= 10.0f) {
+        ESP_LOGI(
+          "POWER",
+          "Voltage Too Low %.2fV",
+          v
+        );      
+        return {"Power Fail"};
+      }      
+
+      if (v >= 10.0f && v <= 20.0f) {
+        return {"Low Voltage"};
+      }      
+
+      if (v >= 20.0f && v <= 30.0f) {
+        return {"Recliner"};
+      }      
+
+      if (v >= 30.0f && v <= VOLTAGE_HIGH) {
+        char buffer[20];
+        snprintf(buffer, sizeof(buffer), "%.1fV", v);
+        return {buffer};
+      } 
+
+      if (v > 48.0f) {
+        ESP_LOGI(
+          "POWER",
+          "Over Voltage %.2fV",
+          v
+        );           
+        return {"Over Voltage"};
+      }  
+
+      return {"Unknown"};
+
+############################## BINARY SENSOR ###############################
+binary_sensor:
   - platform: gpio
     id: in_1a
     name: "Motor 1 Extend"
@@ -130,10 +359,8 @@ binary_sensor:
 
     on_press:
       then:
-        - logger.log:
+        - logger.log: "SFLAG INTERRUPT"
-            "SFLAG INTERRUPT"
+        - script.execute: fault_handler
-        - script.execute:
-            fault_handler
 
   - platform: gpio
     id: en1
@@ -151,21 +378,22 @@ binary_sensor:
       mode:
         input: true
 
+################################## SENSOR ##################################
 sensor:
-
   - platform: adc
     id: supply_voltage
     pin: GPIO4
     name: "Supply Voltage"
     attenuation: auto
     update_interval: 30s
-
+    entity_category: diagnostic
     filters:
       - multiply: 44.4444
 
   - platform: tmp102
     name: "Board Temperature"
     address: 0x4A
+    entity_category: diagnostic
     update_interval: 30s
 
   - platform: wifi_signal
@@ -175,8 +403,21 @@ sensor:
   - platform: uptime
     name: "Uptime"
 
-script:
+  # =====================================================
+  # OTHER SENSORS
+  # =====================================================
 
+  - platform: wifi_signal
+    name: "WiFi Signal"
+    id: wifi_signal_db
+    unit_of_measurement: "dBm"
+    device_class: signal_strength
+    state_class: measurement
+    entity_category: diagnostic
+    update_interval: 30s
+
+################################## SCRIPT ##################################
+script:
   - id: fault_handler
     mode: single
     then:
@@ -241,9 +482,8 @@ script:
       #     );
       #     esp_restart();
 
+################################## INTERVAL ##################################
 interval:
-
-
   # heartbeat
 
   - interval: 1s
@@ -252,13 +492,11 @@ interval:
       - delay: 750ms
       - light.turn_off: heartbeat
 
-
   # motor supervisor
 
   - interval: 10ms
 
     then:
-
       - lambda: |-
 
           //
@@ -304,18 +542,16 @@ interval:
           // VOLTAGE CHECK
           //
 
-          float v=id(supply_voltage).state;
+          constexpr float VOLTAGE_LOW  = ${voltage_low};
+          constexpr float VOLTAGE_HIGH = ${voltage_high};
 
-          if(v < 10.0f || v > 48.0f)
+          float v = id(supply_voltage).state;
+
+          if (v < VOLTAGE_LOW || v > VOLTAGE_HIGH)
           {
-            ESP_LOGE(
+              ESP_LOGE("FAULT", "Voltage %.2fV out of range", v);
-              "FAULT",
+              id(fault_handler).execute();
-              "VOLTAGE %.1f",
+              return;
-              v
-            );
-            id(fault_handler).execute();
-            return;
-
           }
 
           uint8_t output=0;
@@ -347,7 +583,6 @@ interval:
           if(m1b)
             output |= (1<<2);
 
-
           // MOTOR 2
           if(m2a)
             output |= (1<<4);
@@ -365,33 +600,8 @@ interval:
             2
           );
 
-
           // ESP_LOGI(
           //   "motor",
           //   "OUT=0x%02X",
           //   output
           // );
-
-# #############################   
-
-# Enable Home Assistant API
-api:
-  encryption:
-    key: "xxxx="
-
-ota:
-  - platform: esphome
-    password: "xxxx"
-
-wifi:
-  ssid: !secret wifi_ssid
-  password: !secret wifi_password
-
-  # Enable fallback hotspot (captive portal) in case wifi connection fails
-  ap:
-    ssid: "Wren-C5-Test Fallback Hotspot"
-    password: "xxxx"
-
-captive_portal:    
-
-logger: