IPEM SIX ESPHome Integration
This commit is contained in:
Dave Williams | DitroniX | G8PUO
@@ -0,0 +1,217 @@
|
||||
# Dave Williams, DitroniX 2019-2026 (ditronix.net)
|
||||
# IPEM SIX - ESP32-C5 | ATM90E32 | WiFi 2.4/5GHz | Zigbee | Bluetooth | SIX Channel IoT Mains Power Energy Monitor
|
||||
|
||||
# June 2026: Example Code, to demonstrate and test the IPEM SIX
|
||||
|
||||
# Remember!
|
||||
# - Set the BOARD to Use ESP32C5 Dev Module (or similar).
|
||||
# - You can also set the BAUD rate up to 921600 to speed up flashing.
|
||||
# - The SDK does NOT need external power to flash. It will take Power from the USB 5V.
|
||||
# - The Serial Monitor is configured for BAUD 115200
|
||||
|
||||
# The purpose of this test code is to cycle through the various main functions of the board as part of bring up testing.
|
||||
|
||||
# This test code is OPEN SOURCE and formatted for easier viewing. Although is is not intended for real world use, it may be freely used, or modified as needed.
|
||||
# It is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||||
|
||||
# For board configuration, see github.com/DitroniX/IPEM-SIX-ESP32C5-ATM90E32-IoT-Mains-Power-Energy-Monitor/wiki/Arduino-IDE
|
||||
|
||||
# Further information, details and examples can be found on our website or github.com/DitroniX
|
||||
|
||||
# * ditronix.net
|
||||
# * github.com/DitroniX
|
||||
# * github.com/DitroniX/IPEM-SIX-ESP32C5-ATM90E32-IoT-Mains-Power-Energy-Monitor
|
||||
# * github.com/DitroniX/IPEM-SIX-ESP32C5-ATM90E32-IoT-Mains-Power-Energy-Monitor/wiki
|
||||
# * hackster.io/DitroniX/ipem-six-esp32c5-atm90e32-iot-mains-power-energy-monitor-e323bd
|
||||
|
||||
# This YAML code is used to be the equivalent of the Hello World but for the IPEM SIX and both ATM90E32's.
|
||||
|
||||
esphome:
|
||||
name: ipem-six-c5
|
||||
friendly_name: IPEM SIX C5
|
||||
|
||||
on_boot:
|
||||
priority: -100
|
||||
then:
|
||||
- delay: 2s
|
||||
- light.turn_on:
|
||||
id: heartbeat_led
|
||||
effect: "Green Heartbeat"
|
||||
|
||||
esp32:
|
||||
board: esp32-c5-devkitc-1
|
||||
variant: esp32c5
|
||||
framework:
|
||||
type: esp-idf
|
||||
|
||||
# ############################# CONFIG #############################
|
||||
|
||||
# Enable Home Assistant API
|
||||
api:
|
||||
encryption:
|
||||
key: "xxxx="
|
||||
|
||||
ota:
|
||||
- platform: esphome
|
||||
password: "xxxx"
|
||||
|
||||
wifi:
|
||||
ssid: !secret wifi_ssid
|
||||
password: !secret wifi_password
|
||||
|
||||
# Enable fallback hotspot (captive portal) in case wifi connection fails
|
||||
ap:
|
||||
ssid: "IPEM SIX C5 Fallback Hotspot"
|
||||
password: "xxxx"
|
||||
|
||||
captive_portal:
|
||||
|
||||
# ==================== LOGGING ====================
|
||||
logger:
|
||||
# level: WARN # Reduces spam - only shows warnings and errors
|
||||
# level: ERROR # Even quieter (uncomment if you want)
|
||||
# level: DEBUG # Head scratching time.
|
||||
|
||||
# ############################# CODE #############################
|
||||
|
||||
# ========================= SPI BUS (Shared) =========================
|
||||
|
||||
spi:
|
||||
clk_pin: GPIO10
|
||||
mosi_pin: GPIO8
|
||||
miso_pin: GPIO9
|
||||
|
||||
# ========================= HEARTBEAT LED =========================
|
||||
|
||||
light:
|
||||
|
||||
- platform: esp32_rmt_led_strip
|
||||
id: heartbeat_led
|
||||
pin: GPIO27
|
||||
num_leds: 1
|
||||
chipset: WS2812
|
||||
rgb_order: GRB
|
||||
restore_mode: RESTORE_AND_ON
|
||||
|
||||
effects:
|
||||
|
||||
- addressable_lambda:
|
||||
name: "Green Heartbeat"
|
||||
update_interval: 50ms
|
||||
|
||||
lambda: |-
|
||||
static uint8_t step = 0;
|
||||
|
||||
uint8_t b = 0;
|
||||
|
||||
if (step == 0 || step == 2)
|
||||
b = 30;
|
||||
else if (step == 1 || step == 3)
|
||||
b = 10;
|
||||
|
||||
it[0] = Color(0, b, 0);
|
||||
|
||||
step++;
|
||||
|
||||
if (step > 20)
|
||||
step = 0;
|
||||
|
||||
# ========================= ENERGY MONITORS =========================
|
||||
|
||||
sensor:
|
||||
|
||||
|
||||
# ==================== ATM90E32 BANK A CS GPIO6 ======================
|
||||
|
||||
- platform: atm90e32
|
||||
|
||||
id: bank_a
|
||||
cs_pin: GPIO6
|
||||
|
||||
phase_a:
|
||||
|
||||
voltage:
|
||||
name: "Bank A Mains Voltage"
|
||||
id: bank_a_voltage
|
||||
accuracy_decimals: 1
|
||||
|
||||
current:
|
||||
name: "Bank A Current"
|
||||
id: bank_a_current
|
||||
accuracy_decimals: 3
|
||||
|
||||
power:
|
||||
name: "Bank A Power"
|
||||
id: bank_a_power
|
||||
accuracy_decimals: 1
|
||||
|
||||
gain_voltage: 38300
|
||||
gain_ct: 64800
|
||||
|
||||
frequency:
|
||||
name: "Bank A Frequency"
|
||||
|
||||
chip_temperature:
|
||||
name: "Bank A Temperature"
|
||||
|
||||
line_frequency: 50Hz
|
||||
|
||||
gain_pga: 2X
|
||||
|
||||
update_interval: 1s
|
||||
|
||||
# ==================== ATM90E32 BANK B CS GPIO7 ======================
|
||||
|
||||
- platform: atm90e32
|
||||
|
||||
id: bank_b
|
||||
cs_pin: GPIO7
|
||||
|
||||
phase_a:
|
||||
|
||||
voltage:
|
||||
name: "Bank B Mains Voltage"
|
||||
id: bank_b_voltage
|
||||
accuracy_decimals: 1
|
||||
|
||||
current:
|
||||
name: "Bank B Current"
|
||||
id: bank_b_current
|
||||
accuracy_decimals: 3
|
||||
|
||||
power:
|
||||
name: "Bank B Power"
|
||||
id: bank_b_power
|
||||
accuracy_decimals: 1
|
||||
|
||||
gain_voltage: 38300
|
||||
gain_ct: 64800
|
||||
|
||||
frequency:
|
||||
name: "Bank B Frequency"
|
||||
|
||||
chip_temperature:
|
||||
name: "Bank B Temperature"
|
||||
|
||||
line_frequency: 50Hz
|
||||
|
||||
gain_pga: 2X
|
||||
|
||||
update_interval: 1s
|
||||
|
||||
# ========================== TOTALS ============================
|
||||
|
||||
- platform: template
|
||||
|
||||
name: "IPEM SIX Total Power"
|
||||
unit_of_measurement: W
|
||||
device_class: power
|
||||
state_class: measurement
|
||||
|
||||
lambda: |-
|
||||
|
||||
return id(bank_a_power).state +
|
||||
id(bank_b_power).state;
|
||||
|
||||
|
||||
update_interval: 1s
|
||||
Reference in New Issue
Block a user